• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar
  • Skip to footer

Westminster Speed

Westminster Speed & Sound

(410) 857-5300 | CONTACT US | FINANCING AVAILABLE
  • Audio
    • Porsche Upgrades
    • BMW Upgrades
    • Car Audio
    • Digital Signal Processing
    • Ford Bronco Upgrades
    • Marine Audio
    • Motorcycle Audio
    • Powersports Audio and Accessories
    • Satellite Radio
    • Car Audio Repair
  • Convenience
    • Bluetooth Technology
    • Navigation Systems
    • Radar Detectors
    • Rear Seat Video
    • Heated Seats
    • Remote Car Starters
      • Remote Car Starter Models
      • Remote Starter Estimate Request
    • Security Systems
    • Smartphone Integration
  • Accessories
    • 3M Ceramic Coating
    • Paint Protection Film
    • Lighting
    • Trailer Hitches
    • Truck Accessories
    • Truck Bed Covers
    • Truck Steps
  • Driver Safety
    • Backup Sensors
    • Backup Cameras
    • Blind Spot Systems
    • Collision Avoidance
    • Dash Cameras
  • Window Tint
    • Window Tint at WSS
    • Window Tint Estimate Request form
  • About
    • About WSS
    • Why Choose WSS?
    • Customer Reviews
    • Directions
    • Meet The Team
    • Install Bay
    • Showroom
    • Demo Sound Room
    • Contact Us
  • Our Work
    • Client Vehicles
    • Videos
  • Facebook

Single Amplifier Distortion Specs Make No Sense

January 15, 2023 By BestCarAudio.com Leave a Comment

Distortion Specifications

Have you ever looked at something and thought you were only getting part of the story? Many previous articles have discussed amplifier distortion at length but haven’t delved into how power output levels and frequency affect distortion measurements. If you’re looking for the best amplifier for your car audio system, especially for midrange drivers and tweeters, this information should be crucial to your purchasing decision.

Amplifier Distortion Specifications

If you’re browsing a car audio amplifier manufacturer’s website, you’ll see a single specification that’s intended to quantify the amount of distortion an amplifier adds to the audio signal. The CTA-2006-C standard requires that the total harmonic distortion and noise added to the audio signal be specified at an output level that is 50% of the maximum rated output for the amplifier. Of course, that power rating needs to comply with the CTA-2006-C standard as well.

Measuring Amplifier Distortion

When an amplifier is being tested for distortion, the technician or engineer will typically look at the harmonic information and noise added to a single test tone.

Distortion Specifications
This amplifier has a THD+N specification of 0.07527% when powering a 4-ohm load with 1 watt of power.

In the measurement above, you can see the test signal at 1 kHz at a level of 2.0 volts. The second harmonic (labelled with the pink 3) is at a level of -77.10 dBV, or 83.15 dB below the 6.03 dBV (2.00V) test signal. The third-order harmonic (labelled with the pink 1) is louder at an absolute level of -68.18 dBV and a relative level of -74.23 dB. You can see the pattern of even and odd harmonics continue well past 20 kHz. It’s worth noting that this is a good Class AB amplifier and not a poorly designed, inexpensive unit.

Sadly, this single specification is quite incomplete in terms of telling the whole story. Audio measurement and analyzer devices like those from Audio Precision and QuantAsylum can generate distortion graphs across a range of power output levels and frequencies. So let’s characterize this amplifier in terms of the amount of distortion it adds to an audio signal based on the amount of power it produces.

Distortion Specifications
A graph of amplifier output power (in dBV) versus total harmonic distortion and noise for our test amplifier.

Before we dive into analyzing the data, we should explain that the horizontal X-axis scale is in decibel volts, known as dBV. This way of looking at voltage represents the amplifier output level using a decibel scale with 1 volt as 0 dB. Thus, the equation to convert dBV to a voltage is 10 ^ (dBV/20).

The output level of 6.03 dBV, where we measured %THD+N in the first chart, would be 2.00 volts. At the low level, distortion is at 0.075%. At an output level of 22.6 dBV, you can see that the distortion increased. This level is the point where the amplifier started to run into clipping. Maximum power output measurements are specified at the output level that corresponds to a THD+N of 1%. For this amplifier, that would be about 24 dBV, or 63 watts into a 4-ohm load.

At the other end of the scale, you can see that distortion increases as output power decreases. This performance is very typical for a Class-AB amplifier. At very low levels, the harmonic distortion content is buried in the noise created by the amp, which for this unit is at about -105 dBV. Crossover distortion at very low volume levels plays a significant role in adding unwanted information to the audio signal. As the output level increases, the audio signal passes through the transition between the positive and negative output devices at a steeper slope, reducing the time the signal spends in this transition region. As such, distortion decreases relative to the output level.

The CTA-2006 THD+N specification for this amplifier would be 0.02% at the output level of 21 dBV (-3 dB from the maximum power output level). This information doesn’t do a good job of describing how well the amp performs in a real-world application since most of the time, we’re only using a fraction of the power available to drive a speaker. For example, if we have a midrange speaker or a tweeter in a three-way system, we may only need 1/10 to 1/20 of the power a midbass speaker would need, or even less than a subwoofer. Played at high volume levels, a tweeter rarely needs more than a few watts.

So far, in all the TestDriveReview product evaluations we’ve published, the distortion has been specified at the same level as the signal-to-noise ratio. This would be at an output level of 1 watt in a 4-ohm load or 2.00 volts. From now on, we’ll include the Power versus THD+N graphs as shown above so readers can see the entire picture of how the amplifier behaves.

Distortion Specifications
Rockford Fosgate keeps their distortion specifications simple; they rate their amplifiers like this T1000-4ad to produce less than 1% THD+N.
Distortion Specifications
The XM-GS4 four-channel amplifier from Sony has a THD+N specification of 0.05% or less at 1 kHz when connected for a 4-ohm load.
Distortion Specifications
Hertz’s ML Power 4 four-channel amplifier has a distortion specification of 0.08% at 100 Hz when connected to a 4-ohm load.
Distortion Specifications
The AV due from Audison’s Voce series has a distortion spec of 0.04% at 1 kHz into 4 ohms.

Distortion Versus Frequency Response

Another characteristic often overlooked is the amount of distortion an amplifier adds relative to different frequencies. We ran another test on this amplifier to characterize this. We used an output level of 1.95 volts (very close to our 2.00-volt number) and measured distortion at frequencies from 20 Hz to 20 kHz.

Distortion Specifications
Distortion versus frequency for our Class-AB car audio amplifier.

While the numbers don’t vary as much compared to output level changes, you can see that there’s more distortion added at higher frequencies compared to midrange levels.

In an upcoming article, we’ll start all over with a new set of measurements with the three amplifiers we used in the What Do Better Amplifiers Sound Like article a few years ago. We’ll throw in a Class-D amp or two to round out the mix, so you’ll have a benchmark from which to compare solutions.

In the meantime, if you’re interested in purchasing an amplifier for your car or truck, drop by your local specialty mobile enhancement retailer today and ask them about a high-performance solution that will make your music sound amazing!

This article is written and produced by the team at www.BestCarAudio.com. Reproduction or use of any kind is prohibited without the express written permission of 1sixty8 media.

Share this:

  • Click to share on Facebook (Opens in new window)
  • Click to share on Twitter (Opens in new window)
  • Click to share on LinkedIn (Opens in new window)
  • Click to share on Pinterest (Opens in new window)

Related

Filed Under: ARTICLES, Car Audio, RESOURCE LIBRARY

About BestCarAudio.com

BestCarAudio.com is a showcase for the very best mobile electronics retailers in the world and a place to educate and inform interested consumers about existing and emerging technologies.

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

OTHER RECENT POSTS

Car Audio Speaker Installation Location Matters

Car Audio Speaker Installation Location Matters

A while back we published an article that discussed why aiming speakers in a properly designed car … [Read More...]

Understanding Light Color and Illumination

Understanding Light Color and Illumination

We took our first look at measuring light sources a while back as our first step toward … [Read More...]

Product Spotlight: Sony XAV-9500ES Mobile ES AV Receiver

Product Spotlight: Sony XAV-9500ES Mobile ES AV Receiver

Those seeking the ultimate performance from a car audio system know that the result will only be as … [Read More...]

Product Spotlight: Sony XS-163ES 3-Way Component Set

Product Spotlight: Sony XS-163ES 3-Way Component Set

When it comes to speakers for the front of your car or truck, the flagship Sony XS-163ES three-way … [Read More...]

Single Amplifier Distortion Specs Make No Sense

Single Amplifier Distortion Specs Make No Sense

Have you ever looked at something and thought you were only getting part of the story? Many previous … [Read More...]

Product Spotlight: Sony XS-692ES 6x9” Mobile ES Component Speakers

Product Spotlight: Sony XS-692ES 6×9” Mobile ES Component Speakers

Looking for new speakers for your car or truck that will deliver detailed sound and impressive … [Read More...]

Subscribe to Our Website via Email

Enter your email address and receive notifications of new posts by email.

Search our site with any combination of CATEGORIES, TAGS, or KEYWORDS

  • Category

  • Tags

  • Sort Order

  • Keyword

  • » Reset

Contact Us

  • Hidden

Address

Westminster Speed and Sound
202 Pennsylvania Ave
Westminster, MD 21157
Phone: (410) 857-5300

SundayClosed
Monday9:00 AM - 5:00 PM
Tuesday9:00 AM - 7:00 PM
Wednesday9:00 AM - 5:00 PM
Thursday9:00 AM - 7:00 PM
Friday9:00 AM - 5:00 PM
SaturdayClosed

Location


Get Directions to Westminster Speed and Sound

Subscribe to Our Website via Email

Enter your email address and receive notifications of new posts by email.

Copyright © 2023 Westminster Speed and Sound · Privacy Policy · Website by 1sixty8 Media, inc. · Log in · !

 

Loading Comments...